LP Steel Plate Guide: Q690E-LP Specs, Equivalents and Price
- An LP steel plate changes thickness continuously along its length to follow the structural load path.
- Shougang reports that Q690E-LP can provide up to 50% thickness variation, about 10% component weight reduction and substantially lower stress concentration.
- Q690E is approximately comparable with S690QL, but neither grade should be substituted without reviewing chemistry, toughness and project standards.
- Standard Q690E listings provide only a price reference. A variable thickness profile requires an engineered, project-specific quotation.
An LP steel plate, also called a longitudinally profiled or variable thickness plate, places material where a structure needs it most. Unlike a conventional plate with one uniform gauge, its thickness changes continuously along the rolling direction.
Shougang’s Q690E-LP development raises this concept to the 690 MPa strength class. The product targets construction machinery and other weight-sensitive structures that currently use several welded plates to create a change in section.
What is an LP steel plate?
“LP” means longitudinally profiled. During rolling, the mill changes the roll gap while tracking the plate’s position. Consequently, the finished plate can include thick zones, tapered transitions and thinner zones within one continuous piece.
The designer can match the profile to bending moment, fatigue demand or local stress. Therefore, an LP plate is an engineered product rather than a standard stock plate selected only by nominal thickness.
How many welded transitions can one LP plate replace?
The answer depends on the component design. In principle, one LP plate can replace several uniform plates that would otherwise require cutting, beveling, welding and non-destructive examination at every thickness transition.
In one published JFE shipbuilding application, approximately 2,500 tons of LP plate reduced weld length by 700 metres and steel weight by 218 tons. Shougang reports about 10% weight reduction and an 80% decrease in stress concentration for its first engineering-machinery application.
What are the Q690E chemical and mechanical specifications?
The following tables show reference limits for the base Q690E grade under GB/T 16270. They do not replace Shougang’s product-specific Q690E-LP specification, approved drawing or Mill Test Certificate.
Q690E reference chemical composition
| Element | C | Si | Mn | P | S | Nb | V | Ti |
|---|---|---|---|---|---|---|---|---|
| Maximum, % | 0.20 | 0.80 | 1.80 | 0.020 | 0.010 | 0.060 | 0.120 | 0.050 |
| Nominal thickness | Maximum CEV | CEV formula |
|---|---|---|
| ≤ 50 mm | 0.65 | C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15 |
| > 50–100 mm | 0.77 | |
| > 100–150 mm | 0.83 |
The permitted alloy design also includes controlled limits for Cr, Ni, Mo, Cu and B. Buyers should compare the complete ladle analysis and product analysis rather than checking only carbon and manganese.
Q690E reference mechanical properties
| Thickness | Minimum yield strength | Tensile strength | Minimum elongation | Q690E impact requirement |
|---|---|---|---|---|
| ≤ 50 mm | 690 MPa | 770–940 MPa | 14% | Average longitudinal Charpy KV2: 34 J at −40°C |
| > 50–100 mm | 650 MPa | 760–930 MPa | 14% | |
| > 100–150 mm | 630 MPa | 710–900 MPa | 14% |
Thin sections require reduced-size Charpy specimens under the standard. In addition, an LP plate should be tested or qualified at representative thick, transition and thin locations where the purchase specification requires it.
Is Q690E equivalent to S690QL?
GB/T 16270 lists Q690E and S690QL as approximate counterparts. Both belong to the 690 MPa quenched-and-tempered structural steel class, and both address low-temperature toughness at −40°C.
However, approximate correspondence does not mean automatic interchangeability. EN, GB and ASTM specifications use different chemistry limits, impact criteria, dimensional rules and testing conventions.
| Grade or product | Standard / producer | Relationship to Q690E | Buyer warning |
|---|---|---|---|
| S690QL / 1.8928 | EN 10025-6 | Closest published EN counterpart | Verify −40°C impact direction, chemistry, CEV and EN 10029 tolerances. |
| S690Q | EN 10025-6 | More closely associated with Q690D | Its toughness class is not the same as Q690E/S690QL. |
| ASTM A709 Grade 100 | ASTM bridge steel | Closest common ASTM bridge strength class | Not a direct equivalent; project and bridge-authority approval are required. |
| ASTM A514 | ASTM | Comparable high-strength Q&T plate family | Grade-specific chemistry and thickness limits vary. |
| Strenx 700 E | SSAB; former Weldox 700 E family | Commercial 700 MPa class alternative | Use the producer’s current datasheet and welding recommendations. |
| DILLIMAX 690 | Dillinger | Commercial 690 MPa Q&T plate | Not automatically equivalent to an LP profile or GB grade. |
| N-A-XTRA M 700 | thyssenkrupp | Commercial S690QL-class product | Confirm the exact suffix and toughness class. |
| JFE-HITEN 780LE | JFE Steel | Comparable application and strength category | It is a producer grade, not a formal Q690E equivalent. |
What thickness, width and delivery condition should buyers specify?
Shougang has disclosed the strength class, thin-gauge development and maximum thickness variation, but it has not published a complete commercial width, length and minimum-thickness range for Q690E-LP. Therefore, buyers should not copy dimensions from a conventional Q690E stock list.
| Specification item | Available reference | How to state it in an RFQ or purchase order |
|---|---|---|
| Base Q690E thickness scope | Up to 150 mm under GB/T 16270 | State the minimum, maximum and end-zone thicknesses separately. |
| Q690E-LP profile range | Up to 50% thickness difference reported by Shougang | Attach a coordinate table or profile drawing with transition lengths. |
| Width and length | Project-specific; full Shougang range not publicly disclosed | State finished width, total length, flat end zones and trimming allowance. |
| International LP benchmark | Dillinger reports LP plate lengths up to 28 m | Use only as a market benchmark, not as a Shougang guarantee. |
| Delivery condition | Base Q690E is quenched and tempered | Require the actual heat-treatment route on the MTC. |
| Dimensional tolerances | GB/T 709 unless otherwise agreed | Add point-by-point profile tolerance, flatness and camber limits. |
| Ultrasonic testing | GB/T 2970 by agreement | State the inspection standard, acceptance class and tested area. |
What is the Q690 steel plate price in 2026?
Public China supplier listings observed in July 2026 placed conventional Q690E and S690QL plate at approximately US$790–1,190 per metric ton FOB China. This range is an indicative listing reference, not a binding market index or a Q690E-LP quotation.
A custom LP steel plate may cost more per ton because the mill must develop the longitudinal profile, control properties across different thicknesses and complete additional measurements. Nevertheless, the fabricated component can cost less when the profile reduces steel weight, welding, inspection and rework.
| Price factor | Why it changes the quotation |
|---|---|
| Minimum and maximum thickness | Controls reduction ratio, heat treatment and achievable plate profile. |
| Thickness gradient and transition length | More complex profiles require tighter rolling control. |
| Plate width, length and order weight | Affects rolling schedule, yield, transport and minimum order quantity. |
| Impact and through-thickness requirements | Adds alloy cost, testing and production restrictions. |
| UT level and third-party inspection | Adds inspection time, documentation and possible rejection risk. |
| Profile qualification and fabrication trials | Prototype orders may include development and engineering charges. |
What HS code applies to Q690E-LP steel plate?
For a hot-rolled other-alloy steel plate that is at least 600 mm wide and not supplied in coils, HS 7225.40 is a common six-digit starting point. National tariff schedules then add further digits.
Classification is not determined by the marketing grade alone. If customs treats the chemistry as non-alloy steel, headings such as 7208.51 or 7208.52 may instead apply according to thickness. Processing after rolling can also change the result.
How could LP steel plate change China’s high-strength steel exports?
The product gives Chinese mills a route from commodity plate exports toward engineering-led supply. Instead of competing only on price per ton, exporters can offer lower part weight, fewer welded transitions and shorter fabrication time.
However, international adoption will depend on design approval, qualification testing, intellectual-property review and reliable profile control. Exporters should also check anti-dumping scope, countervailing duties and project-specific material approvals before quoting.
What should importers verify before ordering LP plate from China?
Overseas buyers should compare total fabricated cost rather than the plate price alone. In addition, they should qualify the material, the profile and the production route as one package.
Submit a longitudinal profile drawing with coordinates, slopes, transition lengths and flat end zones.
State whether the governing grade is Q690E, S690QL or a project-specific approved specification.
Require MTC chemistry, CEV, tensile data and −40°C impact results linked to the actual heat number.
Define where thickness and mechanical properties will be verified along the plate.
Specify GB/T 2970, EN 10160, ASTM A578 or another agreed ultrasonic acceptance level.
Complete bending, forming and welding-procedure trials before serial production.
Confirm HS classification, trade-remedy exposure, transport limits and seaworthy packing.
TISCO’s broader China supplier qualification checklist explains how to control MTC traceability, tolerances, inspection and packing. Although that guide focuses on stainless sheet, the same procurement controls remain relevant to high-strength plate.
Importers can also review the China import cost and freight framework when comparing FOB, CFR and landed costs. Grade-specific technical requirements must still be evaluated separately.
Frequently Asked Questions about LP steel plate
What is an LP steel plate?
An LP steel plate is a longitudinally profiled plate whose thickness changes continuously along its length. The profile places more steel in high-stress areas and less steel where loads are lower.
Is Q690E equivalent to S690QL?
Q690E and S690QL are approximate 690 MPa class counterparts, but they are not automatically interchangeable. Buyers must compare chemistry, impact testing, dimensional tolerances, delivery condition and the governing project standard.
What is the indicative Q690 steel plate price?
Public China supplier listings for standard Q690E and S690QL plate indicated roughly US$790–1,190 per metric ton FOB in July 2026. Custom LP profiles require a separate project quotation.
What HS code may apply to Q690E-LP plate?
HS 7225.40 is a common starting point for hot-rolled other-alloy steel flat products at least 600 mm wide and not in coils. Final classification depends on chemistry, dimensions, processing and the importing country’s tariff schedule.
Related sourcing and market resources
Q690E-LP availability, dimensions and processing capability require written supplier confirmation. The presence of this technical guide does not state that TISCO holds this product in stock.
Official and technical references
Shougang — Q690E-LP Development | JFE Steel — LP Steel Plate | JFE Technical Report — LP Plate Manufacturing | Dillinger — LP Plate | China National Standards Platform — GB/T 16270 | S690QL / 1.8928 Technical Datasheet | World Customs Organization — HS Chapter 72
© tiscoco.com | This guide is for technical and commercial reference. Chemical, mechanical and dimensional tables describe the base Q690E grade or cited market benchmarks; the final Q690E-LP purchase specification, approved drawing, MTC and engineering calculations govern each order. Prices are indicative public listings, not binding quotations. Equivalent grades are not automatically interchangeable.